| CWF® Hardwoods Clear Wood Finish
penetrates and bonds to exterior wood providing a flexible, long
lasting rich matte finish, even on tough exotic hardwoods such as
Ipe, Pau Lope®, Ironwood and Mahogany. CWF® Hardwoods saturates,
seals and stabilizes wood to minimize cracking, warping and other
damage caused by moisture and sun. The unique formula, combined with
premium U.V.-absorbing transoxide pigments, provides a finish that
accentuates the beautiful color of your wood for years to come.
Available In
• CWF® Hardwoods Clear Wood Finish is tintable to a wide range of
wood colors. A sample brush out on the surface to be coated is
recommended to determine the actual color result. For color
uniformity, intermix in one container all products to be used on an
entire section.
Where To Use
• All new and weathered exterior woods including T1-11, Cedar,
Redwood and Pressure-Treated Wood
• New and weathered exotic hardwoods such as, Ipe, Pau Lope®,
Ironwood, Mahogany and Teak
• Horizontal and vertical surfaces such as decks, siding, fences and
furniture
Surface Preparation
• All surfaces to be coated must be free of all dirt, grease, grime,
mildew and previous coatings.
• Apply to bare wood surfaces or over a previous weathered
application of CWF® Hardwoods. Remove previous stain, varnish or
sealers with Flood® Cleaner Premium Wood Cleaner and Brightener
per label directions.
• Remove mildew with a solution of 4 ounces of non-ammoniated
detergent (TSP), 1 quart of outdoor bleach and 3 quarts of fresh
water. Allow this solution to remain on
the surface for 10-15 minutes, then rinse thoroughly.
• After cleaning allow the wood to dry 2 days or until it has
reached a moisture content of 20% or less before finishing.
Preparation for New Wood
• New wood surfaces have a hard shiny surface called mill glaze that
prevents maximum penetration and bonding of a finish. To properly
prepare the surface for application, treat with a solution of Flood®
Wood Stripper diluted according to label instructions. An
alternative is to sand the surface with 80 grit sandpaper, using a
hand or pole sander. Clean off all loose wood particles. Test wood
for absorbency by sprinkling water on the surface. If water is
absorbed rapidly, the surface is ready for finishing.
Application
• Cover everything you do not wish to coat, including plants and
shrubs.
• Apply between 50° and 90° F. Do not apply in hot sunlight.
• Do not apply if cold, wet weather is expected within 24 hours.
• Do not thin - use as is.
• Apply with one or combination of the following - Brush: High
quality synthetic stain brush, Roller: Synthetic woven cover 3/8-3/4
inch,
Spray: Air-Less Sprayer .011 - .015 fluid tip/ 700-800 psi or less,
or garden sprayer.
• Stir thoroughly before and periodically during application.
• Apply one coat of CWF® Hardwoods.
• Apply a second coat as soon as the wet look dulls (30-60 minutes)
or anytime thereafter.
• After sprayer or roller application, backbrush to improve
penetration
and uniformity of coverage.
• Wipe up or brush out any puddles to avoid shiny areas, (within 30
minutes).
Dry Time
• 24 hours
Coverage
• Rough Surfaces 100 - 150 sq. ft.
• Smooth Surfaces 200 - 350 sq. ft.
Clean Up
• Clean up soap and water.
Maintenance
• Surfaces with harsh exposure to sun, weather or foot traffic could
show wear more quickly than other surfaces. In addition, due to the
dense cell structure of exotic hardwoods, these surfaces may also
wear more quickly. If this happens, a quick and simple cleaning and
recoat is necessary.
|
|
Even brand-new wood can quickly become
gray and dirty from exposure to sun, dirt and rain. Unlike
bleach-based deck cleaners, the gentle ingredients in Flood® Wood
Cleaner remove surface and ground-in dirt without damaging the
sensitive fibers or the wood's natural color.
Where To Use
• Ideal for pressure-treated wood, cedar and redwood.
• Use on decks, siding, fences, and other exterior woods.
Preparation
• Flood® Wood Cleaner is mild and won’t harm plants or shrubbery.
• Carefully sweep all debris off deck surface.
• Wet surface with a garden hose.
• Mix one part Flood® Wood Cleaner to four parts water.
• Do not mix with chlorine bleach or other household cleaning
products. Doing so can result in release of highly toxic gases.
• Mix using only plastic containers in well ventilated areas.
Application
• Apply the cleaning solution thoroughly using a stiff bristle brush
or a roller. If you are hand brushing your deck, remember to wear
chemical-resistant gloves.
• Do not allow the deck to dry during the cleaning process.
• Allow the cleaning solution to work for 20-30 minutes.
• Rinse off the remaining solution thoroughly with clean water.
Dry Time
• Allow wood to dry at least two days before applying a finish.
Clean Up
• Clean tools with soap and water.
LIMITED WARRANTY - Flood® Wood Cleaner
Product Safety Information
|
Ipe Clip Hidden Fastner
